Many espresso machines advertise pre-infusion or pre-brewing. But what actually happens during this process and when is the function useful? We explain why we no longer use the term "pre-infusion," why 3 seconds are always too short, and when you're better off turning the function off. (This article builds on our espresso brewing guide. You'll find the basics there.)
Why we no longer say "pre-infusion"
The term pre-infusion suggests a certain sequence: add water to the coffee, pause, then continue brewing. We consider this pause – sometimes called "blooming" – pointless for espresso. More on that in a moment.
What we mean instead when we talk about this topic: gentle pre-wetting of the coffee puck. That is, slowly add water with reduced pressure or reduced flow to the coffee before full brewing pressure arrives. Without a pause. The difference sounds like splitting hairs, but it's relevant to what happens in your portafilter.
What pre-wetting does
Coffee is hydrophobic. It initially repels water. Dry coffee grounds don't absorb water right away. If you apply full pressure (8–9 bar) to a dry coffee puck, the water encounters resistance and seeks the path of least resistance. The result: channeling, uneven extraction, an espresso that can taste both sour and bitter at the same time.
If you pre-wet the puck slowly, something different happens. The coffee absorbs moisture, swells evenly, and when full pressure arrives, the puck is prepared. Water distributes more evenly, extraction becomes more homogeneous. With many coffees, this results in a rounder, sweeter, more body-forward cup. Not with all – but with many.
A side effect: With pre-wetting, you can often grind finer without the puck choking up and still extract evenly. Finer grind size means more extraction, and that in turn is often very interesting from a taste perspective, especially with complex coffees.
Filter coffee blooming and espresso pre-wetting: two different things
With filter coffee, there's a similarly named technique: blooming. You pour a small amount of water over the coffee grounds, wait 30 to 45 seconds – and watch as the coffee swells and gas bubbles rise to the surface. The CO₂ stored in the coffee cells during roasting escapes freely from the open coffee bed. This isn't a ritual but physics. If this CO₂ were still in the coffee bed, it would block even water flow and also introduce carbonic acid into the beverage. The pause solves the problem. (We explain how this works in detail in our filter coffee brewing article.)
In the portafilter, this is physically not possible. When the portafilter is engaged, CO₂ has no way out – the puck is sealed off by the shower screen. It can only escape downward through the basket, and that happens extremely slowly without active water flow. Even when the pump is running and water is pushing through the puck, current research shows it takes longer for the CO₂ to fully leave the coffee puck than a shot actually takes. A pause without water flow certainly won't achieve this.
The purpose for which blooming works with filter coffee doesn't exist with espresso at all – not because a pause is performed poorly with espresso, but because the system's physics simply doesn't allow a path. The pre-wetting with espresso therefore pursues a different goal: to saturate the hydrophobic coffee puck evenly with water before full pressure sets in. This isn't a CO₂ problem but a wetting problem. And different rules apply to that.
Why the pause doesn't make sense
Many machines implement "pre-infusion" this way: pump on, a few seconds of water, pump off, pause, then pump back on with full pressure. The problem is simple.
If the pump works at full pressure in the first phase and then pauses, you've already shot pressurized water at the puck. The puck is saturated in some spots, not in others. Then comes a pause where nothing happens except the coffee swells unevenly. And then full pressure returns – on an already partially swollen but unevenly wetted puck. That's not gentle, that's counterproductive.
For pre-wetting to work, you need one of two things: Either the pump can reduce its performance for the first phase (less pressure or less flow). Or the machine has a second water path with a smaller diameter that activates during the pre-wetting phase. Both result in the coffee getting wet slowly and evenly before the actual extraction with full pressure begins.
Three seconds of pre-infusion is always too little
Here it gets mathematical. To completely saturate a coffee puck, you need roughly twice the amount of water as the amount of coffee. At 18 g of coffee, that's around 30–36 ml of water.
How fast does your machine deliver this water? Normally, about 4 ml per second flows through the puck. At 4 ml/s you need at least 8–10 seconds to push 30–36 ml of water through the puck. Only then is the coffee puck completely saturated.
Three seconds gets you to 12 ml. The puck is maybe one-third wetted. Five seconds? 20 ml – still not enough. With reduced flow (about 3 ml/s) it takes even longer.

Vibration pump: Your machine already does this
If you have a vibration pump – and that applies to the vast majority of home machines under €2,000 – your machine already automatically does gentle pre-wetting. The vibration pump builds pressure slowly, flow starts low and increases over several seconds. That's exactly a pre-wetting.
What does that mean? If your vibration pump machine additionally offers a "3-second pre-infusion," exactly what happens in those three seconds is what the pump does anyway. In the worst case, the existing pressure is even relieved with the water in the portafilter. Your additional pause has no positive effect. The effect is zero. You only extend the brew time, without changing the extraction.
With some machines – the Ascaso Steel Duo PID is a well-known example – we therefore recommend simply turning off the pre-brewing function. It doesn't make the machine better, and the 5 seconds that are maximum adjustable there aren't enough for meaningful puck wetting anyway.
When pre-wetting really makes sense
It gets really interesting with machines that have a rotary pump and can additionally reduce flow. The Lelit Bianca is a good example: via the paddle you can throttle the flow at the beginning and wet the puck slowly – 9 to 10 seconds with reduced flow, then full pressure. With many coffees, this results in measurably more even extraction.
The prerequisites summarized: You need a machine that can actually reduce flow or pressure in the first phase (not just pause), and you need at least 8–10 seconds of pre-wetting time so the coffee puck is completely saturated.

How pre-brewing affects total brew time
If your machine does pre-wetting, it naturally extends the total contact time. How do you handle it if you have a recipe from a roastery?
Starting point: The recipe says 27 seconds, made with a rotary pump.
You have a vibration pump: Figure about +3 seconds, so around 30 seconds. That's because the vibration pump builds pressure more slowly and the first phase extracts less intensively. (We explain this in detail in the article Espresso extraction time: When does the brew time really start?)
Your machine additionally has pre-brewing with a pause: Then add the pause time on top. If the machine "takes a breath" for two to three seconds after pre-wetting before full pressure builds, you also add this time. In the example: 27 + 3 (vibration pump) + 3 (pause) = around 33 seconds.
But – and this is important – don't obsess over second-precise recipes. These times give you a framework, an orientation. Keep the brew ratio (e.g., 18 g in, 36 g out), land roughly in your time window, and then decide by taste. Your palate will improve from espresso to espresso.
More on brew time and why the first drop isn't the right starting point: Espresso extraction time: When does the brew time really start?
This article is also available as a video on our YouTube channel.
















