You love coffee and strive for the perfect cup? Then you've surely heard about grind size. But how "well" a grinder really grinds depends on far more than just whether the powder is fine or coarse.
That's where particle size distribution (Particle Size Distribution = PSD) comes into play – a decisive factor for extraction and thus for the flavor of your coffee. Over the past few years, we've intensively tested over 70 coffee grinders and delved deep into the world of particle analysis. In this article, we explain what particle distribution is all about, how we measure it, and which metrics really matter.
Also Worth Reading: How slow feeding affects your grinder's particle distribution!
What is particle size distribution (PSD)?
When your grinder grinds coffee beans, it doesn't create just a single particle size, but an entire spectrum – from very fine "fines" to coarser "boulders". Particle size distribution describes exactly this mixture: how many particles of which size are in your ground coffee? How this spectrum turns out depends heavily on the grinding mechanism, that is, whether you're grinding with a conical burr or flat burr.
Typically, we see a so-called bimodal distribution in espresso grounds. This means there are usually two "peaks" (Peaks) in the distribution:
- A fine peak (Fines Peak) at very small particle sizes.
- A main peak (Nominal Peak), which makes up the largest share of the ground coffee and whose position depends heavily on the set grind size.
This distribution is crucial because it significantly influences how water flows through the coffee during brewing and which flavors are extracted and how quickly. An uneven distribution can lead to uneven extraction – some particles are then over-extracted (bitter), others under-extracted (sour).

How do we measure particle distribution? Our protocol
To obtain objective and comparable data, we work closely with the team of the Coffee Excellence Center at the Zurich University of Teacher Education (ZHAW). Our measurements follow a standardized protocol:
- Measurement device: We use a high-precision measuring device based on dynamic image analysis (a Retsch Camsizer X2, affectionately called "Kevin" internally). The coffee particles are guided through a shaft and captured by cameras. Unlike laser diffraction, we thus obtain not only size information but theoretically also shape information, although we focus on size here.
- Sampling: A representative sample is essential. Since finer and coarser particles can separate in the container, we use a sample divider. This divides the ground sample mechanically and fairly, so we obtain a small but representative amount for analysis.
- Standardization: All grinders are tested with the same coffee (a naturally processed Brazilian from the cooperative APAS) and according to defined recipes (T4 = espresso, T5 = ristretto, T6 = lungo, T7 = back to espresso) to ensure comparability.
The most important measured values in detail
From the measurement data, we derive various metrics. The three most important for evaluating a grinder are:
x50 (Median):
x₅₀ (median particle size): This is the average particle size in the statistical sense. More precisely: 50% of particles are smaller than x₅₀ and 50% are larger. That's why x₅₀ is also called the median or D50. For espresso grinds, it typically lies in the several-hundred-micrometer range (e.g., 200–300 µm, depending on grinder and setting). x₅₀ can be considered as an approximate measure of the "average grind size" – it shifts to the left (smaller values) when we grind finer, and to the right (larger values) for coarser grinding. For extraction, a small x₅₀ means: more surface area, potentially higher extraction (up to over-extraction) and slower flow-through. A larger x₅₀ gives less surface area, lower extraction (risk of under-extraction) and faster flow-through. Important: x₅₀ alone doesn't describe the entire distribution, but it's a good starting point for comparing grinds.
🔎 x50 in a nutshell: The x50 value (in micrometers, µm) is the point at which 50% of the volume of ground coffee consists of particles smaller than this value, and 50% of particles larger than it. It represents the "typical" particle size in the ground coffee.
Fine content (Qf <100 µm / Fine peak):
By this we mean the fine content in the ground coffee – specifically the percentage of particles smaller than 100 µm. Why 100 µm? Because in many grinder analyses there's a minimum point around this size between the large main peak and the "fine dust" hill. Everything to the left of that we call fines. This value (often given as Q_<100µm) thus indicates how dusty a ground coffee is. Example: 30% <100 µm means that almost a third of the coffee particles are finer than a human hair is thick – that's quite a bit of "coffee dust".
A high fine content can increase the body of an espresso (intensity, because more fine particles end up in the cup), but also carries the risk of over-extraction and bitterness (the fines release flavors very quickly and tend to over-extract). Additionally, they clog spaces in the puck and increase resistance: grinders that produce many fines often need to be set coarser for espresso to still get a somewhat flowing shot. Conversely, grinders that produce hardly any fines (so-called unimodal distributions with only one peak) can be set much finer without the shot drying up – because there are fewer clogging particles. The fine peak thus significantly determines how a ground coffee handles and tastes: from silky and dense (lots of fine dust) to clear and light (little fine dust).
🔎 Fine content in a nutshell: This value indicates the percentage volume fraction of particles that are smaller than 100 micrometers. These very fine particles are often called "fines" and form the fine peak in the distribution curve. This peak often lies in the range of 30-70 µm.
"Main peak width" (60% Coarse Peak Width):
When we speak of the width of the main peak, we mean the size range in which 60% of all coarse particles (i.e., larger than 100 µm) are contained. The fines, that is, the very fine particles below this threshold, are deliberately excluded. This creates a clear view of what a grinder produces in its "main business": the medium to coarse particles that significantly influence the espresso.
Let's imagine this main area as a mountain landscape without fog: Is the main peak a narrow, clear ridge, where almost all particles have similar size? Or a sprawling hill surrounded by small chains of hills? That's exactly what the 60% Coarse Peak Width shows – it describes how narrow or broad the ground coffee is distributed in the main area.
A small value means: The particle sizes are close together, the ground coffee is uniform. A large value means: The distribution is widely spread – there are both smaller and noticeably larger particles around the average. The consequence: Part of the coffee extracts faster, another part slower – this can lead to flavor inconsistency.
Why does this matter? Because a narrow distribution suggests more uniform extraction – with balanced, clean flavors. If the distribution is wide, medium-sized particles and coarse chunks ("boulders") often lie side by side in the puck. The latter yield little flavor – they under-extract, while the rest is already optimal or even over-extracted. The result: acidity and bitterness stand disconnected side by side, sweetness is lost.
In our tests with over 70 grinders, it has shown: Once the main cloud becomes wider than about 300 µm, espressos often taste "scattered" – little structure, little harmony. A lower peak width, on the other hand, is typical for modern grinders with precise burrs and stable alignment. They consistently produce good ground coffee – the foundation for clear, extraction-stable espresso.
🔎 In short: The 60% Coarse Peak Width doesn't measure the width at 60% of the curve height, but rather the size range containing 60% of the coarse particle mass. It's an objective measure of the uniformity of the main portion in the ground coffee – and thus a key indicator of grinder quality.
Understanding particle distribution curves
When we look at the results of particle measurement, we usually see two curves: an incremental and a cumulative distribution. Both show the same ground coffee sample – but from two different perspectives.
Important: The X-axis in both diagrams – that is, particle size – is logarithmically scaled. This means: The distance between 10 µm and 100 µm looks the same as the distance between 100 µm and 1000 µm – even though the second range encompasses ten times more size difference.
Why is this important? Because it easily tricks the eye:
- In the incremental curve, the area below 100 µm often appears wider than it actually is – although in reality there's very little space there.
- In the cumulative curve, a steep rise in the 200–300 µm range can suddenly look much more dramatic because the distance appears visually small but is actually large in content.
In short: The X-axis is not linear but follows a logarithmic scale – this is necessary to display both fine and coarse particles clearly in one graph. But: It changes our sense of "area" and "weighting". Whoever reads the curve should keep that in mind.

Example of an incremental distribution.
Incremental distribution ("Incremental Share")
The incremental distribution (Incremental Share) looks like a small mountain range. It shows how many particles occur in a certain size range. The Y-axis indicates what fraction (in percent) of the total ground coffee falls within a narrow size interval – for example, between 240 and 250 µm. The higher a point on the curve, the more particles are in exactly that range. You immediately see: Where's the highest "mountain"? How many fines are there? And how wide is the whole thing spread? This makes the incremental distribution the visual map of the grind size – it reveals where the majority of particles lie, how pronounced the fine peak is, and how homogeneous or scattered the ground coffee appears overall.
- The incremental curve shows you what percentage of the coffee powder falls into a specific size range (e.g., how much lies between 30-100 µm).
- It visualizes the peaks very clearly – you recognize the fine peak and the main peak and see whether the distribution is bimodal. The X-axis (particle size) is often logarithmically displayed here to make the fine range more visible.
- If there's a value of 2% on the Y-axis at 250 µm (X-axis), that means: → Approximately 2% of the total measured coffee consists of particles that are approximately 250 µm in size (more precisely: in the measurement interval around 250 µm).
Example of a cumulative distribution
Cumulative distribution ("Cumulative Share")
The cumulative distribution (Cumulative Share) tells the same story – but in a different way. Here, the Y-axis shows what percentage of the coffee is already accounted for when we sum up all particles up to a certain size. The curve starts on the left at zero and then rises steadily – until it reaches 100% on the right. The slope changes are particularly interesting: A steep section means that many particles are present in this size range – real action is happening in the coffee there. A flat section means: not much is happening here, only a few particles are in this size range. You could say: The cumulative curve shows how quickly the bag of coffee fills up when we fill it with particles from fine to coarse.
- This curve shows the total fraction (in percent) of all particles that are smaller than or equal to a certain size.
- It always rises from 0% to 100%.
- From this curve you can easily read the x50 value (where the curve crosses the 50% line) and also the fine content (the Y value at 100 µm on the X-axis).
Why these values influence flavor
Now it gets exciting: how do these distribution properties translate into the cup? Here both empirical experience and scientific findings come into play. For one thing, trained tasters quickly notice when an espresso, for example, due to too many fines tastes over-extracted-bitter or due to too coarse particles remains watery and sour. On the other hand, analyses – such as by astrophysicist and coffee researcher Jonathan Gagné – have made it clear that when dialing in an espresso, we're essentially adjusting the fine content. In an evaluation of 24 espresso grinders from our test series, Gagné found that different grinders at optimal settings produce surprisingly similar amounts of fines – regardless of the average particle diameter. In other words: Baristas turn the grind size mainly until the total amount of fines is right to achieve the desired flow-through and pressure.
A "fines-loving" grinder must therefore be set much coarser (so too many fines don't clog the puck), while a "fines-free" grinder can be set very fine (to build enough resistance in the puck at all). This interplay explains why, for example, unimodal grinders (with few fines) often require very fine shots, which then deliver exceptionally clear flavor notes – this is often called "low-fines shots," which emphasize lighter acids and floral notes. Conversely, grinders with deliberately a bit more fines often deliver stronger, fuller-bodied espressos with thicker texture – classically Italian with more bitter-chocolate character, but sometimes rougher in acidity too. The width of the main peak is also reflected in flavor. In our tests, we repeatedly found that very broad distributions (high main peak width) lead to complicated flavor combinations: a certain restlessness in the cup, you might say, which we also describe as "scattered." Some of the extraction goes too far (bitterness, sometimes a metallic note), some falls short (sharp acidity), and it's hard to achieve a balanced overall flavor.
When particle sizes are instead more homogeneous (narrower peak), the flavor usually comes together more harmoniously – sweetness, acidity, and bitterness are in accord, nothing stands out unpleasantly. That doesn't mean every grinder with many fines or broad distribution automatically makes bad coffee. Taste judgments depend on many factors (bean variety, roast, recipe, etc.), and you can balance a lot with technique. Nevertheless: the trends are clear. Grinders that grind very uniformly are valued by many coffee enthusiasts for their clear, balanced shots. Grinders that produce more fines often yield strong, dense shots that are more difficult to dial in perfectly. Here, personal taste also decides: some like the chocolatey punch of a slightly "dirty" espresso, others love the transparent nuance of a "clean" espresso – both can be excellent in their own way. Particle distribution, however, gives us the scientific tools to make such grinder characteristics tangible and work with them deliberately.
Of course, these three values are also interconnected: Often, grinders with many fines (high fine content) produce a somewhat broader distribution and a larger x₅₀, because you have to set them coarser. Conversely, grinders with few fines often have a smaller x₅₀ (must be set finer) and a narrower main peak. Nevertheless, it's worth examining each metric individually to understand the complete picture.
Conclusion: What we can learn from particle analysis for the perfect coffee
The exploration of particle distributions impressively shows that the seemingly simple act of grinding coffee contains a hidden world of science. For us coffee lovers, this means: we can approach the subject more consciously. When we understand that a grinder doesn't just grind "fine" or "coarse," but produces an individual fingerprint of fines, average particles, and maybe a few boulders, we can then better tailor our coffee recipes to it – or choose the grinder that suits our preferences.
Different grinding discs of the same size with different geometries, such as cutting, pre-breaking, and tightness of cutting edges, also change the particle distribution very significantly.
The insights from particle analysis inspire us to look more closely (or taste more carefully) at the next espresso: Do I taste hints that my grinder produces many fines? Does the espresso taste silky, heavy, perhaps with a certain dryness in the aftertaste and less clarity in the flavors? Then that could be an indication of a high fine content.
Or is it crystal clear in its complexity and the individual notes of the coffee stand out – but the body is perhaps a bit less pronounced and maybe juicy and not heavy and dense? Then that might be a sign of very homogeneous, fines-free grinding.
Ultimately, particle distribution shows us how closely craftsmanship and science are intertwined in coffee. The best results occur when we use both: the curiosity and experimental enthusiasm of the home barista and the knowledge from research. Our journey through the world of coffee particles has shown that behind every flavorful cup lies a lot of physics and statistics – but don't worry: you don't have to be an astrophysicist to benefit from it (even if people like Jonathan Gagné certainly help!).
Even a basic understanding of what happens in ground coffee can help us make more conscious decisions. Whether it's investing in a particular grinder or fine-tuning our recipe – scientific measurements like particle analysis give us an objective foundation to understand the myth and magic of espresso a bit better.
In the end, it's about the taste in the cup. Particle distribution is not an end in itself, but a key that helps us decipher and control flavor. So when we next talk about "coarse" or "fine," let's remember: there's much more to it – an entire particle world waiting to be discovered. Have fun exploring further and on your way to the perfect coffee!![]()

















