Home / Coffee knowledge / Our power measurement
    Nachhaltigkeit
    Unsere Leistungsmessung

    Our power measurement

    Tobias Milz koordiniert den Nachhaltigkeits-Bereich der Kaffeemacher:innen. Er sammelt und erarbeitet Wissen, mit dem wir selbst mehr über den Fußabdruck des Kaffees entlang der Kaffeekette lernen. Das ermöglicht, dass wir selbst besser werden. Gleichzeitig stellen wir alles was wir lernen dem Markt zur Verfügung, um eine sozial-ökologische Transformation der Kaffeebranche voran zu treiben. Tobias ist aber auch ein Allrounder: als gelernte Koch ist er auch an der Sensorik-Front unseres Unternehmens aktiv und als Programmierer schmiert er unsere Schnittstellen. Ein bunter Fähigkeiten-Mix, angetrieben durch Neugier und eine ordentliche Portion Kaffee-Begeisterung.

    We have revised our power measurement protocol to ensure greater comparability and create transparency. To do this, we took a closer look at how energy labels are measured and critically questioned our own measurements.

    It was important to us to develop values that reflect everyday use and can make it more efficient.

    The article explains how we measure, how the results come about, and introduces our equipment. We now measure espresso machines with all technologies. If a machine does not have a steam function, the corresponding measurement is omitted. If a dual boiler does not have the option to shut off the steam boiler, we continue the protocol without this measurement.

    Otherwise, we perform the measurement once with and once without the steam function.

    Measuring instruments

    Power measurement

    To achieve precise and reliable values, appropriate measuring instruments are a prerequisite. That's why we acquired three Christ CLM1000 Professional (Plus). The Christ CLM1000 Professional (Plus) provides second-by-second measured values for power consumption and energy consumption at a resolution of one tenth of a watt-hour. This corresponds to 0.0 Wh or 0.0000 kWh.

    The measuring instrument transfers the measured values via USB and we can save and evaluate them as CSV.

    Measurement setup

    Preparatory work

    In our first power comparison protocol, we set a heating time to achieve high comparability. But that doesn't reflect actual use and penalizes machines that heat up faster and are brew-ready. Why should you wait 25 minutes at home when the machine is ready after 10 minutes?

    That's why we try to empirically and in consultation with the manufacturers determine when the machine is really at brewing temperature. The exchange with the manufacturer gives us a target value, which we verify with our measurements (see temperature measurement protocol).

    When is an espresso machine considered temperature-ready?

    A machine is considered ready when the target temperature of 92 °C in the portafilter is reached with the first pour (extraction shot). A previous 5-second flush with the portafilter locked in is performed to accelerate the heating of the portafilter (flush shot).

    Depending on the machine and function, we determine the starting temperature with and without the steam boiler.

    The heating time is taken into account for the power measurement. After heating, the extraction power measurement begins.

    Conducting the power measurement

    Measurement with steam boiler

    We perform the power measurement in parallel with a temperature measurement. For both measurements, the test machine must be "cold." For this, a rest time from last use of at least 6 hours is defined. The water tank is filled with water at room temperature (20 - 24 °C) to maximum capacity. The machine is unplugged and plugged in and switched on once the measuring instruments are ready.

    Once the machine is ready after the predetermined time, 5 extractions of 26 s ± 1 s are made (procedure for temperature measurement is covered in the Temperature Measurement section). Before the first extraction, a 5 s flush with the portafilter locked in is done once (part of the heating phase), and one minute is waited between extractions. Then, before each extraction, 2 s is flushed and then extracted. The 2-second flush is also called "flushing" and simulates cleaning of the shower screen.

    Then we draw 5 x 70 g ± 5 g of hot water from the hot water dispenser to simulate an Americano. Here too, we wait one minute after each pour. If the machine has the ability to adjust steam power, the steam draw is always measured at maximum power.

    In a final phase, energy consumption is measured in "idle" mode. For this purpose, we leave the machine on for at least 20 minutes.

    One test machine, one test series

    Data collection is done on one test machine and in one test series. There can be slight control-related deviations from machine to machine.

    Evaluation of power measurement

    For the evaluation, we always take the timestamp and energy value from the CSV file and enter them into the measurement table.

    Generally, the data should be read as follows:

    • End heating = Beginning espresso extraction,
    • End espresso extraction = Beginning Americano,
    • End Americano = Beginning milk steaming
    • End milk steaming = Beginning warming

    However, if there were pauses in the measurement, they are taken into account in the evaluation. Data points always consist of two values: timestamp t and consumption E at this point in time. tAA = 11:12:12 = Time point heating start and EAA = 0 = Heating start

    Heating

    We take the first data point from the measurement and the data point that can be taken after the previously set time. Here there is also a check to see if the first extraction then starts.

    Calculation: EA = EAE - EAA

    Example: 0.1000 kWh = 0.1000 kWh - 0

    Espresso extraction consumption

    Calculation: EE5 = EEE - EEA

    Example: 0.0077 kWh = 0.1200 kWh - 0.1023 kWh

    Calculation: EE1 = EE5 / 5

    Example 0.00154 kWh = 0.0077 kWh / 5

    Espresso measurement

    Hot water consumption

    Calculation: EA1 = EHE - EHA

    Example: 0.0050 kWh = 0.1250 kWh - 0.1200 kWh

    Hot water measurement

    Steam / milk steaming consumption

    Here we also note the value we have set for the steam draws. For example: tD = 25 s

    Calculation: ED5 = EDE - EDA

    Example: 0.0100 kWh = 0.1250 kWh - 0.1200 kWh

    Calculation: ED1 = ED5 / 5

    Example 0.0020 kWh = 0.0100 kWh / 5

    Steam measurement

    Warming consumption

    By warming, we mean "ready for immediate use," i.e., neither standby nor energy-saving mode.

    Calculation: EW = EWE - EWA

    Example: 0.0150 kWh = 0.1450 kWh - 0.1250 kWh

    Calculation: EW60 = EW / (tWE - tWA) * 3600 s

    Example: 0.1800 kWh = 0.0150 kWh / (14:10:00 - 14:05:00) * 3600 s

    Espresso, Americano and Cappuccino consumption

    For the calculation of an espresso, as well as for the calculation of a cappuccino, we included the heating time. We conducted a survey in our community with 2,700 participants. This examined typical usage behavior. One finding related to regular heating and drawing coffee: in most cases, it heats up to then perform one or two draws.

    Therefore, we include the heating time in the consumption calculation for a draw.

    Espresso calculation: EE = EA + EE1

    Cappuccino calculation: EC = EA + EE1 + ED1

    Kaffeemacher protocol consumption (EKM)

    In the older videos, our consumption figures always refer to a heating time of 25 minutes and 5 draws with 1 minute pause between draws. So that we also have comparability with the old videos, we provide this value as EKM.

    Please note here that the older values can be comparatively high for machines with faster heating time.

    Kaffeemacher protocol calculation: EKM = EA + EE5

    Measurement without steam boiler

    Feedback and measurement standard

    This measurement protocol has been tested in practice several times and has evolved through feedback from espresso machine manufacturers. Thanks for the differentiated feedback to Holger Dreißig from Xenia Espresso as well as Julian Thomas and Patrick Lieser from Profitec.

    Xenia uses the power measurement protocol to optimize and develop comparison values with other espresso machines. Profitec and ECM also use the measurement protocol in development and to gather comparison values.

    Do you have questions about our measurements? Have you already measured your own machines? We look forward to your feedback and comments.

    If you would like to learn more about energy optimization or other sustainability articles in the coffee sector, sign up here for our corresponding newsletter.

    An overview of all previous power measurements

    What do you think?

      Which machine should we test next?

      Espresso machine or grinder: Tell us what should be next on our test bench. We read every request.

      We only use your email to follow up on your request. You'll only receive the newsletter if you check the box and confirm. Privacy Policy