The tamping pressure when tamping has little influence on espresso extraction. We wanted to scientifically validate this finding from daily practice. For this purpose, we worked with the support of a food technologist to extract, measure, and vary the tamping pressure on 150 espressos. In this article, we present the results to you.
What is Tamping?
Tamping is the pressing of ground coffee powder in the portafilter. A tamper is used for "tamping," which consists of a handle and a metal base that is pressed into the portafilter like a piston. The metal base corresponds to the inner diameter of the basket. If the gap between the basket wall and tamper diameter is too large, part of the coffee powder will not be pressed sufficiently.
By pressing the ground coffee, uniform water distribution is enabled. The brewing water should encounter the same resistance on the ground coffee surface at all contact points. If the ground coffee is not compacted enough in places or if there are air pockets below the pressing point, there is a risk of channeling. This can be prevented through careful preparation of the ground coffee, vertical compacting, and even tamping.
Instructions: Preparing Espresso Step by Step (Articles and Videos).

Three classic tampers with a 58mm diameter.
Research Question: What Influence Does Tamping Pressure Have?
Two aspects were examined. First, we wanted to find out whether changing tamping pressure affects the flow time. Second, we investigated whether tamping pressure has an effect on extraction yield and thus on the concentration of dissolved coffee particles in the cup.
To obtain the most precise results possible, work steps and methodology were defined precisely.
Materials
Rancilio Specialty, commercial espresso machine with precise flowmeter. However, each espresso shot was double-checked with the Acaia Luna.
Etzinger etzMax, espresso grinder with integrated scale. However, all grinds were rechecked by weight and repeated if there was a deviation (see methodology).
Puqpress, automatic tamping machines for commercial use. Tamping pressure adjustable.
VST Refractometer, for measuring TDS in percent, that is, the concentration of dissolved particles in the beverage in relation to water.
VST Syringe Filter Attachment, to filter solids from coffee solution and measure only the dissolved particles with the refractometer.
VST Syringe

Etzmax Espresso Grinder and Puqpress
Methods
The espresso grinder is set to an output of 18.5 g. Ground coffee results between 18.4 g and 18.6 g are used.
The Rancilio Specialty espresso machine is programmed to an output water amount of 45 ml and a brewing temperature of 93 °C.
The corresponding amount of coffee is ground directly into the portafilter. The coffee is then leveled with fingers and tamped with the Puqpress. The portafilter is locked into the machine and extraction begins.
The amount in the espresso cup is measured on the scale. After extraction, the portafilter is removed and tapped out.
A flush shot is pulled on the espresso machine.
After extraction, the espressos are set aside to cool. After cooling, they are stirred and the TDS value is measured with the refractometer.
The espresso is drawn into the refractometer through the syringe filter attachment using the syringe.
This procedure is repeated 50 times each for tamping pressures of 10 kg, 15 kg, and 20 kg.
Data evaluation for flow time and TDS values is performed using a one-way ANOVA with a specified error probability of 5%.
Results Flow Time and Tamping Pressure
In the variance analysis of flow time, no significant difference could be found. In other words: regardless of whether pressing was done at 10 kg, 15 kg, or 20 kg, our measurements did not vary noticeably due to pressing pressure.

Effect of tamping pressure on extraction time.
| 10 kg Pressure | 15 kg Pressure | 20 kg Pressure |
| 26 | 20 | 27 |
| 21 | 23 | 25 |
| 23 | 26 | 29 |
| 24 | 27 | 28 |
| 23 | 25 | 24 |
| 24 | 26 | 27 |
| 25 | 26 | 23 |
| 24 | 29 | 25 |
| 26 | 20 | 26 |
| 31 | 24 | 27 |
| 25 | 23 | 25 |
| 24 | 23 | 21 |
| 25 | 22 | 26 |
| 27 | 23 | 21 |
| 24 | 30 | 24 |
| 24 | 24 | 21 |
| 25 | 22 | 24 |
| 27 | 21 | 25 |
| 23 | 21 | 28 |
| 31 | 24 | 22 |
| 25 | 24 | 22 |
| 24 | 25 | 24 |
| 22 | 30 | 23 |
| 27 | 20 | 25 |
| 22 | 21 | 22 |
| 25 | 23 | 25 |
| 25 | 21 | 21 |
| 24 | 21 | 22 |
| 24 | 27 | 21 |
| 23 | 22 | 24 |
| 27 | 23 | 22 |
| 21 | 22 | 30 |
| 24 | 24 | 21 |
| 25 | 21 | 25 |
| 24 | 25 | 29 |
| 25 | 24 | 26 |
| 23 | 24 | 23 |
| 23 | 23 | 24 |
| 23 | 23 | 24 |
| 22 | 23 | 23 |
| 21 | 22 | 24 |
| 26 | 24 | 26 |
| 23 | 25 | 24 |
| 25 | 22 | 20 |
| 24 | 23 | 27 |
| 20 | 23 | 22 |
| 24 | 26 | 25 |
| 24 | 22 | 26 |
| 22 | 21 | 22 |
| 23 | 24 | 20 |
| Groups | Count | Sum | Average | Variance |
| Column 1 | 50 | 1212 | 24,24 | 4,51265306 |
| Column 2 | 50 | 1177 | 23,54 | 5,60040816 |
| Column 3 | 50 | 1210 | 24,2 | 6,08163265 |
| Source of Variation | SS | df | MS | F | P-value | F crit |
| Between Groups | 15,4533333 | 2 | 7,72666667 | 1,43133301 | 0,242301 | 3,05762065 |
| Within Groups | 793,54 | 147 | 5,39823129 | |||
| Total | 808,993333 | 149 |
| Fk(0,05) | 3,05762065 |
The test statistic F is smaller than the critical F value, so there is no significant result. The actual P value exceeds the specified error probability of 5%. Therefore, no significant difference can be found between the groups.
Results TDS Values and Tamping Pressure
In the variance analysis of TDS values, no significant difference could be found either. The concentration of dissolved coffee particles was not substantially affected by different tamping pressures.

Effect of tamping pressure on concentration of dissolved particles.
| 10 kg Pressing | 15 kg Pressing | 20 kg Pressing |
| 8,53 | 7,77 | 8,15 |
| 7,99 | 7,94 | 8,15 |
| 8,03 | 8,02 | 8,16 |
| 8,13 | 8,03 | 8,27 |
| 8,01 | 8,08 | 8,2 |
| 8,01 | 8,06 | 8,08 |
| 8,1 | 8,07 | 8,08 |
| 8,05 | 8,26 | 8,01 |
| 8,2 | 8,12 | 7,96 |
| 8,24 | 7,96 | 8,03 |
| 8,17 | 7,98 | 7,99 |
| 8,15 | 7,99 | 8,03 |
| 7,91 | 7,85 | 8,11 |
| 8,09 | 8,02 | 8,02 |
| 8,09 | 8,88 | 8,02 |
| 8,09 | 8,12 | 8,01 |
| 8,11 | 8,11 | 7,93 |
| 8,15 | 7,99 | 8,04 |
| 7,96 | 7,99 | 8,04 |
| 8,3 | 8,05 | 7,99 |
| 8,25 | 8,15 | 7,99 |
| 7,99 | 8,2 | 8 |
| 8,07 | 8,28 | 7,99 |
| 7,99 | 7,81 | 8 |
| 7,81 | 7,84 | 7,97 |
| 7,8 | 7,92 | 8,01 |
| 7,93 | 7,9 | 8,01 |
| 7,94 | 7,87 | 7,66 |
| 7,86 | 7,97 | 7,8 |
| 7,93 | 7,88 | 7,89 |
| 8,06 | 8,02 | 7,99 |
| 8,08 | 8,02 | 8,02 |
| 7,99 | 7,95 | 7,92 |
| 8,04 | 7,7 | 7,99 |
| 8,05 | 7,89 | * |
| 8,13 | 8,01 | * |
| 8,2 | 8,11 | * |
| 8,19 | 7,95 | 7,91 |
| 7,98 | 8,02 | 7,96 |
| 7,94 | 8,07 | 7,7 |
| 7,82 | 7,94 | 8,01 |
| 8,08 | 8,04 | 8,08 |
| 8,08 | 8,05 | 7,92 |
| 8,07 | 7,96 | 7,83 |
| 8,06 | 7,97 | 8,03 |
| 7,88 | 7,78 | 7,97 |
| 7,88 | 8,01 | 7,97 |
| 7,93 | 7,81 | 7,91 |
| 7,97 | 7,73 | 7,65 |
| 7,96 | 7,85 | 7,69 |
TDS values. *missing measurement values in these cells
| Groups | Count | Sum | Average | Variance |
| Column 1 | 50 | 402,27 | 8,0454 | 0,01824167 |
| Column 2 | 50 | 399,99 | 7,9998 | 0,03163465 |
| Column 3 | 47 | 375,14 | 7,98170213 | 0,01635356 |
| Source of Variation | SS | df | MS | F | P-value | F crit |
| Between Groups | 0,10546284 | 2 | 0,05273142 | 2,37573217 | 0,0965805 | 3,058928 |
| Within Groups | 3,19620383 | 144 | 0,02219586 | |||
| Total | 3,30166667 | 146 |
| Fk 0,05 | 3,058928 |
| Fk 0,1 | 2,33979948 |
The test statistic F is smaller than the critical F value, so there is no significant result. The actual P value exceeds the specified error probability of 5%. Therefore, no significant difference can be found between the groups.
Raw Data and Measurements from the Tamping Test
The raw data and further information can be found in the Excel sheet. If you can derive any further interesting insights, we would love to hear about the results.
Download Tamping Project Results
Analysis of the data revealed a linear correlation between the following datasets for extraction time and the determined TDS values, which was determined using the Bravais-Pearson correlation coefficient:
- Tamping pressure 10 kg: Extraction time and TDS: weak positive correlation -> r=0.5068
- Tamping pressure 15 kg: Extraction time and TDS: strong positive correlation -> r=0.6854
- Tamping pressure 20 kg: Extraction time and TDS: weak positive correlation -> r=0.5423
where: |r|=1 -> perfect linear correlation
|r|=0 -> no linear correlation
Pressing Pressure, Taste, and Additional Information
Within the scope of this test, the taste of the espresso was not examined. Therefore, we cannot make any statements about it. However, based on the insights from the test, we interpret that varying pressing pressure in the range we examined has no or only marginal influence on taste.
Also, based on our test, we cannot make any statement about how pressure lower than 10 kilograms affects extraction. Based on research and partner feedback as well as our own experience, we recommend pressing with at least 6 kilograms of pressure when tamping.
Discussion
In examining the question of whether tamping pressure affects the extraction time of espressos, no influence could be demonstrated. However, this does not mean that no influence exists, only that in the test model used, no influence could be demonstrated. Interfering factors include, for example, inaccuracies in preparation and insufficient precision of the examination machines used.
The equipment used is designed for professional use in gastronomy and not for precise laboratory equipment.
However, there are far greater interfering factors in practice when preparing an espresso than in the experimental procedure used.
Therefore, in practice, we should not assume a major influence of tamping pressure on extraction, since there are many inconsistent parameters affecting the extraction process. In this, tamping pressure is merely one parameter among many.
---
The tamping test was conducted by Michel Aeschbacher in collaboration with a food technologist who wishes to remain unnamed. We are grateful for your contribution!
We are open to further research partnerships and are happy to use our materials and expertise to develop insights on all things coffee-related.![]()
















