Good thermoblocks are rightfully the rising stars in the espresso machine sky. And the Quick Mill Luna is riding in the slipstream of another popular dual-thermoblock machine into the fast lane. Responsible for this, in addition to Quick Mill's good manufacturing quality, is the relatively affordable purchase price: we find the machine in Germany starting from 1200 euros and in Switzerland from 1400 francs.
The elephant in the room is the Ascaso Steel Duo PID, which costs 1900 euros in Germany and roughly the same in francs in Switzerland. Can the Quick Mill Luna keep up at a significantly lower price? In this test report, we look at the Luna's performance. In another one, we'll compare the machines directly (Q4 2024).
Quick Mill Luna Overview
It's a pleasure to start with positive aspects, of which there are several. The Quick Mill Luna is a thermoblock from Quick Mill. The family-run company, founded in 1945, manufactures its machine in Senago near Milan. The Luna's manufacturing quality leaves nothing to be desired in our test. The curved stainless steel housing feels premium and we find no sharp edges, not even on the drip tray.
The espresso machine is equipped with two thermoblock elements, with 600 and 1000 watts power consumption respectively. Parallel steaming and espresso brewing is possible because both units operate independently.
At 12 kilograms, the Quick Mill Luna sits stable on the table. 35.7 cm height and a width of 28.8 cm meet a depth that varies due to the protruding plug and portafilter as follows:
- The base depth is 32.3 cm,
- with the plug the machine measures 33.2 cm
- and with the portafilter we measure 39.7 cm.
The distance between the portafilter outlet and the drip tray is 9.3 cm. This is practical for larger cups or for those who like to use a scale under the cup to monitor the amount of coffee in the cup. (This is something that makes absolute sense with the Luna, despite the volumetrics.)
The Quick Mill Luna is equipped with programmable volumetrics, which we'll discuss in more detail below. The steaming time and water output time for tea water can also be programmed. The tea water output is more precisely described as rather a tea water trickle, which is dispensed via the steam wand. Not much comes out!
The Luna comes with the typical Quick Mill tamper, which closes cleanly with the edge. While this tamper fits, non-Quick Mill equipment has poor prospects once again. Both the portafilter's 3-prong bayonet is incompatible with other espresso machines, as well as the flat seat of the baskets. This is typical of Quick Mill. Tampers larger than 58.2 mm don't fit well, let alone baskets from other manufacturers. No question: Quick Mill technology works for itself. The lock-in effect is especially unfortunate, given the numerous tools available in the 58 mm portafilter range.

Heat-up Time and Temperature Performance
Anyone who wants to drink espresso quickly in the morning or during the day will appreciate a fast heat-up time. Thermoblocks generally have an edge over espresso machines with boilers here due to the aluminum block's good thermal conductivity and the direct heat transfer to the brewing water. With the Quick Mill Luna, we measure a heat-up time of 8 minutes to reach a temperature of 92 degrees on the first shot. An extra minute or two does the machine good. This is by the way a statement we can also back up on the basis of our protocols. The longer the machine is on, the more stable it becomes, especially with a higher sequence of shots.
With few shots after the heat-up time of 8 or even 20 minutes, the machine is not stable! The shot temperatures fluctuate significantly. While we measure an average temperature of 92.8 degrees on the first shot, the third shot averages only 89.23 degrees—and we're talking about seconds 5 to 25 of extraction. All shots tend to overshoot at the beginning and then fall during the shot, stabilizing again toward the end. Over the 5 shots in the Kaffeemacher temperature protocol, we measure a maximum temperature difference of 7.63 degrees! The standard deviation (STDEV) is 2.77. This is the worst value we've ever measured with this protocol.

Interestingly, the Quick Mill Luna improves under frequency and with longer stand time. With the WBC protocol, we pull 14 shots with a frequency of ultimately 35 seconds between extractions. The goal is to test performance under load, e.g., for gastronomy. The standard deviation value of 1.18 over 14 shots can certainly compete with many dual boilers. Even though the difference between minimum and maximum temperature of 5.74 degrees over all shots is still a relatively high value. These values are also due to the Luna not quite being at temperature on the first shots of the series. Only from shot 5 does the Luna reach stable 92.7 degrees and maintains that well with only one spike up over the next 9 shots.
In this context, one phenomenon should not go unmentioned. The PID controller, which can be adjusted easily via the display, repeatedly shows a different temperature. This can also be seen in our video, where in the middle of the video the temperature inexplicably drops to 89 degrees on the display and we have to wait for it to stabilize again.
Consequences of Temperature on Espresso Taste
What influence does all this have on espresso extraction? Difficult point. Ideally, the fluctuating temperature has no influence if you hit the right target window. However, our measurements show that the Luna does not deliver reliable temperature performance. Sometimes you get the temperature you want. But it often fluctuates significantly—especially on the first and second shots. And those are the ones that matter to us in everyday use.
Therefore: if precise temperature is important to you, the Quick Mill Luna is not a good choice!
This doesn't mean you can't pull very good espresso with the thermoblock. And in the end, the taste in the cup is what matters.
By the way: our machine's offset was set well from the factory. It's set to 9 and we only had 1 degree deviation from the display. (Depending of course on how each shot went. Difficult. 😟)

Strong Energy Performance
In terms of power consumption and energy usage, the Luna ranks among the best machines on the market. 5 double shots including heat-up time draw only 0.08 kWh with the steam boiler switched off. An espresso with heat-up is brewed at 0.038 kWh. If we add the steam boiler, we come to a value of 0.11 kWh for shots. A cappuccino then requires 0.092 kWh.
These are good values!
Steaming in the Slow Lane
In terms of steaming speed, the Quick Mill Luna ranks last in our test series. The thermoblock needs 80 seconds to bring the milk to temperature. That's really slow. The machine's power is enough to get the milk rolling. But it takes a lot of time. Only the small pitcher steams any better. If you take the time, you can make good foam with the Luna. That's not the problem. And once you get used to the machine, you'll probably have little to complain about the slow steaming. Compared to other machines on the market, however, it's very, very slow.
When steaming, it makes sense not to make a clear separation between the rolling and stretching phases. It's better to continuously roll a little air into the milk while the entire milk circulates. If bubbles become too large, there's a risk they won't be broken down due to the low rolling power.
Volumetrics, Pressure Relief, and the Puddle
The Quick Mill Luna has programmable volumetrics. That would be a strong argument for the machine if it worked precisely. Unfortunately, the amount of output fluctuates with the resistance of the coffee puck, so the volumetrics is actually not usable, or only usable if the grind is already perfectly set and no factors change. If, for example, you come back to the machine after a day, you'll almost certainly have varying amounts of coffee in the cup. A scale helps with this, allowing you to manually monitor the espresso output amount. This is by the way also the procedure for all espresso machines with the Faema E61 group head—so nothing special. But the programmable buttons promised us more.
What's unfortunately missing is a pressure relief valve, so the pressure after extraction initially remains on the puck. That's why we often find a puddle here and if we remove the portafilter too quickly, there's a risk that the coffee grounds will splash back at us. Not nice for an espresso machine that costs over 1000 euros. Others in this price range do much better.
At least this has the side effect that we only have to clean the shower head, but don't need to backflush to clean the machine.
Conclusion on the Quick Mill Luna
The Quick Mill Luna leaves me puzzled above all because of its poor temperature performance. It's usually roughly at temperature, but not a reliable partner when it comes to precision. I find it problematic that especially the first shots are not consistent, because I see the machine's purpose really lying with this use case. A solution is probably only to pull some warm water through the portafilter first to stabilize the machine. The WBC protocol shows that the Luna improves significantly after that.
In terms of manufacturing quality, the machine is exemplary, especially for the asking price. We've seen machines that cost 1000 euros more and have significantly more plastic or sharp edges.
The machine's steam power is sluggish. The circulation is adequate, but the heating happens very slowly.
Compared to other dual-thermoblocks, the Quick Mill Luna is significantly cheaper. In the same price range, however, there are also some entry-level dual boilers. These have all the arguments on their side, especially in terms of consistency and steaming performance, but are slower when it comes to heat-up time. But are fast heat-up time, good manufacturing quality, and low energy consumption enough as main arguments to buy the Luna? I have my doubts.
What do you think? Do you have the machine at home and are very happy with it? Did we overlook something important? We look forward to your comments and feedback.
![]()
















