The ECM Synchronika is a dual boiler espresso machine from the German company ECM. We tested the Synchronika 1 and in 2024 the Synchronika 2. In this article you will find our compiled results for both models, temperature curves and our video reports.
If you have gathered your own experiences with the ECM Synchronika, we look forward to your comments. This complements our test and helps other interested parties get a more comprehensive picture of the machine in everyday use. Thank you!
Since the ECM Synchronika I will continue to be sold for a while longer, we will keep the information about this machine as it is. All information that applies exclusively to the ECM Synchronika II can be found further down in the article: Jump to the new ECM Synchronika II
General information and facts
The ECM Synchronika is an espresso machine with enormous scope, weight, material quality and value retention. This machine was built to outlast time. All components radiate this.
We measure a width of 33.5 cm, a height of 41 cm without cups and with our own cups a height of 45 cm. This can be interesting for you if the machine is to stand under a low wall cabinet in the kitchen. The ECM Synchronika is already 48.5 cm deep in its base. With the portafilter inserted, the Synchronika reaches a depth of 59 cm. This combines the machine to a considerable weight of 30 kilograms.

The ECM Synchronika has a high-gloss polished stainless steel housing. It looks beautiful, reflects wonderfully and unfortunately collects numerous fingerprints. The polishing cloth will need a permanent place near the espresso machine.
The Synchronika is equipped with a 2 liter steam boiler and a 0.75 liter brew boiler. The rotary pump is very quiet and purrs like a kitten during extraction. We measure the remarkably low value of only 59.2 decibels. We read from the community that for some the machine rattles much more. We identified such rattling and sliding on the drip tray, but this can be bridged with magnets or rubber holders.
The rotary pump, however, allows us to connect the machine to mains water. A waste water hose can also be attached to the drip tray. We fill it with a maximum of 850 ml if it is not connected to the waste water and if we still want to carry it to the sink.
The water tank holds 2.5 liters, can be removed via a lid from the top and is of high quality. The water is drawn via a valve in the bottom.

Delivery contents
The ECM Synchronika is one of the espresso machines that comes with a good accessory set that really makes sense. Sometimes manufacturers go overboard with accessory items that then have inferior quality themselves. The ECM Synchronika comes with two beautiful, heavy portafilters that are perfectly balanced and have an appearance that matches the Synchronika very well.
Like the toggle levers, they have a trapezoidal tip made of polished stainless steel, which is finished with a black hard plastic setting. A perfectly fitting heavy tamper with a finger-width base is a noble tool that does ECM great honor.
Also included is a cup stand that elevates the espresso cups and thus ensures that the pours always hit the cups. The stand is nevertheless made in such a way that a scale fits both on it and next to it.
Anyone who wants to connect the ECM Synchronika to mains water will find the connection hose already in the delivery package.
Temperature curves
Once the ECM Synchronika has reached its thermal equilibrium, it is a relatively temperature-constant espresso machine. But it takes... We waited 35 minutes until the Synchronika reached 93 degrees brewing temperature with all important components. While the boiler reaches temperature much earlier, the E61 brew group and portafilter are so heavy that it takes the stated time to really reach temperature.
The following graph shows in orange a warm-up phase of the ECM Synchronika. After 25 minutes we made the first extractions, one per minute. With the 4th extraction, we had reached the target temperature of 92 degrees in this case with the portafilter. The graph below that also illustrates this well.
After 35 minutes we were nearly at the target temperature with the gray curve, which in this case was 93 degrees (shown in yellow as a bar with +/- 1 degree at 93 degrees). Here too a flush shot is necessary, which heats the portafilter well, as even after 35 minutes it is not sufficiently up to temperature on its own (see also graph 3.)

The WBC protocol shown in the first graph begins after one hour and then simulates various inactivity intervals. The temperature curves make it clear that the ECM Synchronika reaches temperature very quickly during extraction and achieves the target temperature after 7 to 8 seconds. After that it runs very consistently. The consistency during extraction is extraordinarily good.
However, when cycling every 1 minute, the machine drifts slightly upward in temperature and becomes increasingly warm. This is a typical problem with Faema E61 espresso machines and is also the case with the Synchronika. The target temperature is therefore not really reliable. Home baristas must get to know their machine very well in order to estimate at what temperature they are currently brewing.
Espresso quality with the ECM Synchronika
The ECM Synchronika has everything a good espresso machine needs. It has high temperature stability during extraction, is well made and relies on a first-class rotary pump. Nevertheless, there remains some uncertainty about after what time the machine is really at what temperature. The ECM Synchronika shares this problem with all Faema E61 espresso machines and the Synchronika offers no solution for it either.
We have drunk very good espressos, both those with a stronger structure and complex specialty coffees. The Synchronika delivers what it takes with sufficient warm-up time. However, with shorter warm-up times or even under frequent use, there are also outlier espressos.
Energy consumption
The long warm-up time is needed to bring the large boilers up to temperature. This of course also has consequences for energy consumption.
We measure 0.43 kilowatt-hours after a 25-minute warm-up time and the extraction of 5 double shots. This corresponds to our standardized protocol, which we apply to all machines. It should be noted that we would have needed to wait a further 10 minutes to measure the machine at full temperature. We will provide this measurement later. The result is likely to be slightly higher. But even as it is, this is a high value for dual boiler espresso machines. Some thermoblocks manage with less than a quarter for the same amount of espresso extraction.
Steaming and milk
Steaming with the ECM Synchronika is a breeze. The machine brings good power with its 2-liter steam boiler to get the milk completely moving. At the same time, the milk is not heated too quickly, which allows for a pleasant rolling phase. This makes the ECM Synchronika a good hybrid machine for households that value both good espresso and milk-based drinks like cappuccino or Flat White.
Conclusion on the ECM Synchronika I
The ECM Synchronika is certainly a wonderful machine. It makes good espressos and froths fine-pored foam for cappuccino and the like. But the test also leaves me somewhat puzzled. For all my appreciation of the manufacturer and the local specialist dealer network - to me the machine seems dated. The Faema E61 brew group recently celebrated its 60th birthday. The guarantee of durability is also a symbol of inertia and is rarely encountered in combination with real innovation. This is evident in the long warm-up time and high power consumption. If you are looking for volumetric extraction control or programmable pre-infusion, you will search in vain with the ECM Synchronika.
Anyone who concludes poor environmental performance from the high energy consumption does not factor in the robustness and longevity of the machine. The specialist dealer network mentioned above has repaired the Synchronika and similar machines for the last 50 years and will continue to do so for the next 50 years. Therefore, an investment in the ECM Synchronika should also be seen as a long-term investment. If you care for your Synchronika, you will probably not buy another machine in your lifetime.
So who is the ECM Synchronika the right machine for? Perhaps for you, if you desire durability and longevity. If you don't want to overwhelm yourself with numerous adjustment options, but instead want a high-quality, very good espresso machine from a German manufacturer that will accompany you for a very long time.
Specialist retailers we recommend
We search for specialist partners whose work and service we know are good. We are in close contact with the dealers. These are affiliate links. If you order through this link, it won't cost you any more, but we get a small commission that we invest in new test equipment.
Update: New ECM Synchronika II presented
At the end of June 2024, ECM presented the new Synchronika 2 at the World of Coffee in Copenhagen. Compared to the Synchronika 1, there is an update that is revolutionary for the espresso machine type with Faema E61 brew group and makes the Synchronika II the fastest heating-up espresso machine with E61 brew group. Two heating cartridges with 200 watts each are built into the brew group. These are actively heated until the warm-up time is reached and thus significantly accelerate the warm-up time of the espresso machine. We measure a warm-up time of 8 minutes! This is the fastest value we have ever measured for an E61 brew group. The previously fastest modified E61 brew group we measured comes from Sanremo and was used in the You. Here the warm-up time was 15 minutes. The steam boiler, by the way, is not up to speed after 8 minutes. You'll need to wait a few more minutes for that.

Temperature curve after 8 minutes very good!
After the warm-up time of 8 minutes, the ECM Synchronika II shows very good temperature performance. We measure a standard deviation over 5 extractions of only 0.63° Celsius. In the first extraction, we measure a maximum temperature difference of 1.7° Celsius between second 5 and 25 of the extraction. Over all 5 extractions, we come to a value of 2.15° Celsius, with the average temperature at set temperature of 93° Celsius at 92.63°.
After an extended downtime of the machine, we also notice an increasing temperature with the ECM Synchronika 2, typical for espresso machines with Faema E61 brew group.

Power measurement and energy consumption of the Synchronika II
Of course, the fast warm-up time also has major impacts on energy consumption. Especially if we omit the steam boiler, we measure a consumption including warm-up of only 0.17 kWh for 5 extractions. Through the rapid warm-up we save electricity on the one hand, on the other hand the two heating rods of course consume electricity. Nevertheless, the value for a dual boiler of this scale is a good value. If we additionally switch on the steam boiler, the energy consumption for 5 extractions is 0.31 kWh, which is still a good value for a dual boiler. Bravo ECM!
















