Pagaia is the Italian word for paddle. Lelit uses this term for the lever that has allowed manual control of the pump during espresso extraction since the Mara X3. The Mara X3 was the first machine with this control. Since October 2026, the Elizabeth 3 and Victoria 3 also come with Pagaia, and they feature an expanded control system: a pressure sensor and storable pressure profiles.
On this page, we collect what we know about Pagaia: how the control system works technically, what lever angle on the Mara X3 means what flow rate, and how the Elizabeth 3's control differs from the Mara X3's.
How Pagaia works technically
Traditional flow control on an E61 group head works mechanically: a needle valve narrows the water path, the pump continues at full power, and the rest is throttled. Lelit does this itself on the Bianca. Pagaia does it differently. The lever controls the pump's power electronically and in real time via pulse width modulation. So instead of braking, less water is delivered from the start. The technology is based on patents from Sage, the parent company of Lelit.
This has two practical consequences. First, you hear the control: at reduced flow, the vibration pump on the Mara X3 drops below 50 dB. Nice mechanical feedback that tells you more during brewing than any gauge. Second, the pressure on the Mara X3 is not a target but a result. You control the flow, and the pressure adjusts as a consequence of the resistance in the coffee puck. If you're coming from pressure profiling, you need to rethink this.
Mara X3: which angle means what flow rate
This is the question we're asked frequently. We measured it on the Mara X3:

The Pagaia lever is located on the left side of the machine. It does not control valve position but pump power.
The 10 o'clock position is a sensible starting position for pre-wetting the coffee puck because the puck becomes evenly saturated without you immediately tearing channels.
Start with the lever at 10 o'clock, wait until the first drops appear at the spout, then turn fully open. This is how we brewed our Toca espresso from Mexico: around 40 grams in just under 30 seconds. The result was caramel and creamy with a long aftertaste.
And if you don't feel like playing with it: set the lever to full flow and brew classically. Pagaia doesn't force you to do anything.
What Pagaia can't do on the Mara X3
Reproducibility. You brew manually, you need to develop a feel for when the puck is saturated and when to turn up. That's fun if you're in the mood for it. If you want the same espresso reliably in the morning without thinking, this isn't for you. There's no volumetrics on the Mara X3, and no shot timer either.
This is exactly where the Elizabeth 3 comes in.
Elizabeth 3: Lever plus storable pressure profiles
The Elizabeth 3 has the same basic mechanism—the pump is controlled here too via pulse width modulation. Added to this is a pressure sensor that measures during extraction how much resistance the coffee puck puts up against the pump. The display shows the pressure on the coffee and the set profile during extraction. The Elizabeth 3 operates in two ways that differ significantly from each other.
Via buttons you run pressure profiles. Each of the two extraction buttons stores a profile with up to five stages. For each stage, you set the pressure in half-bar increments and the duration. Unlike on the Mara X3, here you specify a pressure and the machine regulates the pump to achieve it. In our test, for example, we chose eight seconds at 3 bar for pre-wetting and then 8.5 bar for the remaining 17 seconds. If you like, you can create a lever profile with all five stages that ramps up to 9 bar and then drops a bar every few seconds.
Via the lever you control manually. With Pagaia, you start the extraction directly at the side and regulate the pump during extraction, as on the Mara X3. This is handy when you want to try a recipe or a shot gets out of hand. In our test, an extraction ran too fast toward the end. With the lever, we braked and landed at 22 to 23 seconds; at 9 bar, the coffee probably would have rushed through in 19 seconds.
On the Mara X3, you control flow exclusively by hand, and nothing is stored. On the Elizabeth 3, storable pressure profiles and the lever are two separate paths. If you start via a button, you can't switch to the lever mid-extraction, and the lever cannot be combined with a stored profile. The buttons also work with time control, which the Mara X3 lacks. Neither machine has volumetrics.
How well this works in the cup depends on the Elizabeth 3 less on the control than on the temperature. After 20 minutes, the first extraction at a set 94 °C is at 93.6 °C. Temperature drops about 2 degrees per minute over five extractions, with a two-minute break between extractions it stays within 0.9 degrees. All measured values, programming step by step, and our recipe are in the Lelit Elizabeth 3 test.
Which Lelit has which Pagaia configuration
| Machine | Type | Lever | Pressure sensor with display | Storable profiles | Dosing |
|---|---|---|---|---|---|
| Mara X3 (PL62X3) | Dual boiler | yes, controls flow | no | no | manual |
| Elizabeth 3 | Dual boiler | yes, only without stored profile | yes | 2 buttons, up to 5 pressure stages each | Time control |
| Victoria 3 | Single boiler | yes | yes, according to Lelit | programmable pressure profiles, according to Lelit | not yet verified |
We tested the Mara X3 (50.2 out of 100 points) and the Elizabeth 3 (61.7 out of 100 points). The information about the Victoria 3 comes from Lelit and has not been measured.
What does Pagaia cost
In Brussels, we were told of a surcharge of 300 euros for the Elizabeth and Victoria compared to the version without the lever. With the market launch prices, this cannot be verified. The Elizabeth 3 costs 1,649 euros in stainless steel and 1,699 euros in black or white; the Victoria 3 according to Lelit 1,149 and 1,199 euros. The Elizabeth PL92T without Pagaia can be had today for around 1,000 euros. The Mara X3 has Pagaia built in; the price there is 1,699 euros, around 500 euros above the previous model.
Lelit equipment prices have been heavily discounted by major international retailers in recent years. Machines were sometimes 200 to 400 euros below the RRP. We'll see where equipment with Pagaia stabilizes.
Why Lelit can do this now
Lelit has been part of the Breville Group since 2022, the company that appears in Europe as Sage. In Brussels, we were told that there is a large portfolio of patents there that Lelit can draw from. After years in which we've made jokes at trade shows about new paint jobs as innovation, technologies are finally coming together visibly here.
Conclusion
Pagaia is not a gimmick. On the Mara X3, we got real flow profiling in a classic dual boiler, and it was fun. With the Elizabeth 3, Lelit takes a step further: there are storable pressure profiles in a price range where they haven't existed before, plus the lever for manual extractions.
The limits of both machines lie less in the control than in temperature. On the Mara X3, temperature stability failed the stress test; on the Elizabeth 3, the small brew boiler loses about 2 degrees with many consecutive extractions. With the Victoria 3 as a single boiler with a small boiler, it will be interesting to see if gentle pre-infusion takes place in a stable temperature window. The Victoria 3 is on our list.
Further reading: our Lelit Elizabeth 3 test, our Lelit Mara X3 test with all measured values for Pagaia, our Lelit Elizabeth PL92T test, and our Lelit Victoria test. Find an overview of all Lelit machines on our Lelit page. How we measure is explained in our testing protocol.
















