The Lagom P80 by Option-O is grinder number 100 in our test field. You requested it as our milestone grinder, and it delivered numbers we've never seen in over a hundred tested grinders. Ordering directly from the manufacturer in Germany costs around 1,600 euros including tax and shipping. For that you get 80 mm flat burrs, a 500-watt brushless motor, an adjustable speed from 300 to 1,700 RPM, and a single-dosing grinder that follows the basic form of its smaller sibling, the P64.
Three things we'll mention upfront. The main peak in the particle distribution is the narrowest we've ever measured. The retention is 0.2 grams. And the grind scale is hard to excuse for a grinder in this price range. In order.
Build and Technology: The Larger Sibling of the P64
Anyone familiar with the P64 will recognize the P80 immediately. Everything is a bit larger, a bit more powerful, which is also due to the burr size. 8.1 kilograms at 24 × 14 × 38 centimeters, milled from anodized aluminum and stainless steel. Internally, however, Option-O has rebuilt almost everything: the upper grinding chamber is now a single-piece component, loose springs and separate bearings are gone when disassembling. The burrs sit magnetically on a three-point mount, two-screw burrs in M6x7 format also fit.
Two details stand out positively in everyday use. The dosing ring closes cleanly with the sieve. And you can grind directly into the 58 mm portafilter without having to adjust anything on the sides.
The knocker at the grinds outlet warrants criticism. It effectively helps expel remaining coffee powder. But the mechanism is so tightly dimensioned that it occasionally gets stuck at the bottom and only comes back after a slight shake. We've also heard about this from course participants. For me personally, the design feels strange: I don't want to milk my grinder. And at the gap, the knocker is almost flush at the top but stands a millimeter out at the bottom.

Buy Option-O Lagom P80
The following specialty retailers* carry the Option-O Lagom P80 and we can recommend purchasing from these businesses.
Germany: Coffee24
* We search for specialty partners we know do good work and provide good service. We're in close contact with the retailers. These are commission links. If you order through this link, it doesn't cost you more, but we get a small commission that we invest in new test equipment.
Noise and Speed: 9 Seconds for 18 Grams, 82.8 dB
At 1,100 RPM, our measurement speed for blocks two and three, the P80 needs nine seconds for 18 grams. With a full hopper, it dispenses 26.2 grams in ten seconds. That's remarkable because the beans are deliberately fed slowly via the screw. Despite the throttled supply, the 80 mm burrs grind through quickly.
During continuous operation, we measure 82.8 dB. According to our protocol, that's in the mid-range, and purely by the number, the grinder wouldn't be quiet. But the number doesn't describe it well here: the sound is pleasant, a full motor noise that I compare to an electric car in the test video. No resonances, no squealing. Even in purge mode at high speed, it remains bearable.
Thermally, the grinder is unremarkable. The beans go in at 21.7 °C, over five consecutive grindings with 20-second intervals we measure 29.9 / 26.0 / 26.7 / 29.3 / 29.8 °C, averaging 28.3 °C. The series doesn't increase, so the grinder doesn't heat up even with multiple consecutive shots. That's exactly right for light and dark roasts.
Retention: 0.2 Grams, Better Than We've Ever Measured
For retention, the P80 delivers the value against which all future single-dosing grinders must be measured. Andrea in our test team is responsible for this measurement and proceeds uncompromisingly: loosen every screw, brush out the burrs from below, scrape together everything that can be found. He managed with difficulty to get 0.1 gram temporarily and 0.1 gram permanently. So 0.2 grams absolute.
The practical consequence is bigger than the number suggests. You can switch beans without grinding anything away first. You can adjust the grind setting and see the effect immediately in the next shot, instead of having to push through half a portion of old stock first. And the coffee in the basket is the coffee you just ground. That's exactly the idea of single dosing, and Option-O did the right detailed work here. We'd like to see a few other manufacturers follow their example.
This is achieved through two things: the knocker, which is tuned to the angled grinding chamber, and a purge function that ramps up the speed at the end of grinding and blows out the rest from the chamber. The grinder recognizes via a torque sensor when resistance decreases, ramps up once and then shuts off. If you want, you can also trigger purge manually with a double press. The other values fit this: of 18 grams of beans fed in, 17.9 grams land in the cup, that's 0.1 gram deviation. Over five portions, the standard deviation is 0.04 grams. Both are outstanding.
As with the P64, we recommend tapping the top of the grinder by hand after grinding. Be careful not to accidentally move the grind adjustment. We did that in testing with a firm tap.
The Grind Scale Is the Biggest Criticism

The P80 adjusts steplessly via a fine thread, and Option-O specifies ten micrometers per line. In practice, that means: one line corresponds to eight to ten seconds of extraction time depending on the coffee. A half line gave us six to eight seconds difference in pull shots multiple times. At grind setting 0.65 we were at 22 and 23 seconds, at 0.6 then at 28 seconds.
That's a problem because there are no intermediate markings between the vertical lines on the dial. So you have to work between the lines but can't tell exactly where you landed. 8.1 or 8.15 or 8.16 looks the same. Michel photographs the setting with every coffee for that reason, and even with that he doesn't hit the position exactly. The reference line on the housing is thicker than the lines on the dial, and the spacing between lines isn't even consistent: the distance from 3.5 to 3.6 looks clearly different from 3.6 to 3.7.

For a grinder whose strength is precision, this undermines part of that precision. For a single-dosing grinder where you switch between recipes multiple times a day, it's the most expensive design flaw in the entire machine. If you always grind the same coffee, you'll barely notice it. If you switch beans daily, photographing will become standard practice.
Dear Option-O team: You build sensational grinders. Make the scaling finer and consistent. And until then, a cleanly printed scale to stick on would be an interim solution you could ship. Individual users are currently putting this together themselves on platforms. For a 1,600 euro grinder, that shouldn't be the customer's job.
Replicability: The Main Peak Returns, the x50 Doesn't
For the adjustment test, we switch from espresso (T4, grind setting 0.7) to ristretto (T5, 0.55), then to lungo (T6, 0.95) and visually back to the starting mark (T7).
The main peak comes back almost exactly: 106.0 µm at T4, 110.0 µm at T7. The x50 value, however, shifts from 144.8 to 172.3 µm, a good 27 µm. Meanwhile the fine peak drops from 44.1 to 39.8 percent. So the uniform main fraction is back, but the rest of the curve isn't. And because with this grinder it's precisely the fines that build resistance in the puck, you feel that in the cup.
Practical consequence: purely visually turning back to the old mark isn't enough. What shows up in our measurement data as inaccuracy is largely due to the coarse scale above. Michel notes that with practice it definitely works, but it requires building a relationship with this grinder. So the P80 grinds reproducibly well once you've got the scale under control.
Particle Distribution: Main Peak at 106 µm, Never Measured This Narrow
We measure particle distribution in cooperation with the Coffee Excellence Center at ZHAW on the Retsch Camsizer X2. In the espresso setting at 1,100 RPM (T4), the x50 is 144.8 µm, the main peak is 106.0 µm, and the fine peak is 44.1 percent; that's the proportion of grinds under 100 micrometers.
The 106 micrometers is the value we planned this video for twice. We tried SSP burrs, 80 and 100 dimensions, blind and non-blind mounted. We've never found such a narrow main peak. For comparison: we classify everything beyond about 300 µm peak width as heterogeneous, and good espresso grinders typically land somewhere between 150 and 250 µm.
The feed system is responsible for this. A screw slowly and evenly delivers the beans to the burrs, and integrated into the Mizen-80OM burrs is a crusher that pre-breaks the beans before they enter the cutting zone. Slow feeding then, just built-in instead of dosed by hand. The burrs sit additionally screwless mounted from the rear, which reinforces the cutting edges and consistency of the grinder once more. Screws set from the top are actually one of the most extreme interventions in burr grinder behavior overall.
The apparent contradiction in the numbers is interesting. The main peak is extremely narrow, yet 44.1 percent of the grinds are under 100 micrometers. That's no accident but a requirement: because the main fraction is so uniform and in the intermediate range there are barely medium and small particles above the 100-micrometer threshold, we have to grind so fine on the other side that we have enough fine content to even build sufficient resistance and reach reasonable extraction times. We know the same pattern from all-purpose burrs.
During the shot, though, the grinder or rather the grinds behave differently. Instead of seeing the first drops after over 13 seconds like with all-purpose burrs, we see the first drops already after around nine seconds. Unlike with the AP burrs, the puck also retains its integrity much longer and settles at a stable 4 milliliters per second toward the end. So the P80 accelerates but noticeably less brutally than expected.
Who is this curve made for? For light, complex roasts definitely. But our tests with various roasts have proven that medium to dark roasts also work very well and retain body. What you need though: clean puck preparation. Because of the high fine peak, clumps form, and without WDT, channeling is a real risk! For this grinder, that's not a recommendation, it's a prerequisite.

RPM from 300 to 1,700: What Speed Changes
You adjust the speed with a detented dial with number scale on the side, from 300 to 1,700 RPM. Because we pulled three samples with the same grind mark, we can show what speed does to the curve.
| Espresso Setting | x50 | Main Peak | Fine Peak |
|---|---|---|---|
| 300 RPM (T4_1) | 153.5 µm | 98.2 µm | 42.4 % |
| 1,100 RPM (T4) | 144.8 µm | 106.0 µm | 44.1 % |
| 1,700 RPM (T4_2) | 146.0 µm | 106.1 µm | 43.6 % |
At 300 RPM the main peak becomes slightly even narrower and the fine peak drops slightly. That's the setting for maximum clarity. Between 1,100 and 1,700 RPM, however, the curve barely changes, which is unusual for a grinder with RPM adjustment.
From the data and also looking at other slow-feeding experiments, we interpret this to mean that slow feeding here already reduces the chaotic distribution and grinding in the grinder so drastically that slower speed doesn't additionally benefit. Read more about that in our article on slow feeding.
Static, Cleaning, and Operation
The grinds strings we affectionately called that with the P64 are history. An ionizer reduces static charge, and basically you don't need RDT anymore. Some residual charge remains, and it increases the darker and finer you grind. For everyday use at home we'd still work with water spray. But that's no longer a requirement like with the P64, it's a comfort improvement. A clear difference from the previous model.
To clean, you remove the catch ring and loosen two hex sockets, then you're at the grinding chamber. That's simple and logically laid out, but it's not entirely tool-free. That's why we rate cleaning as good, not very good. For quick cleaning between grindings you don't need to unscrew anything, for deep cleaning you do. If you additionally want to work with grinder cleaner, we have Cafetto Grinder Clean in our shop.
On the side sit two buttons: a real on-off switch that locks in, and the grind button that runs the grinder until the torque sensor recognizes the end of grinding. Zero calibration is simpler than the P64, a limiter protects the burrs during calibration and can be removed if you want full control.
In the Cup: Light to Decaf
In the test video we deliberately brewed at standard nine bar without flow or pressure profiling. Not because it's the best solution, but because nine bar is most common and not many machines can regulate flow and pressure.
The first espresso was a light roast, our Shyira. Incredibly complex, with everything this coffee has in it and surprisingly much body. Heavy but elegant, thick, with a creaminess that lingers in the mouth. We didn't expect that with this particle picture, we were leaning more toward a lighter, juicier body. First drop at eleven seconds.
Then our interpretation of an Italian espresso, the Compadre. Fat-caramel, with a cocoa note so clear and tangible you could write it down. Sweetness fully present, a medium to heavy body, as it cools toward caramelized nuts and dark chocolate. The acidity in this coffee is low anyway, but what's there is clearly structured. Set to 24 seconds and it tastes good at 26 or 28 seconds too, so the range isn't pinpoint limited.
To finish, the Apas Decaf, decaffeinated in Bremen with subcritical CO₂, so with natural carbonation. Decaffeination significantly changes a coffee's structure and thus its extraction behavior: this coffee doesn't accelerate toward the end, the flow even drops. We've never seen that before. In the cup the nougat note we know from Apas Espresso, our reference coffee from the test protocol.

Apas Decaf, Decaffeinated Espresso from Brazil
The coffee from the last pull in the video: sweet and cocoa-forward, nougat and dark chocolate, plus extraction behavior that acts quirky with the P80.
Across all three coffees: the espresso potential of this grinder is outstanding. But it's not a grinder for beginners. You need an understanding of extraction, brewing, and clean puck preparation. The path to the sweet spot is a narrow ridge over a wide river: too fine and you have a clogging moment, and you're working close to that edge. Grinders with this particle picture show their strengths most clearly on machines that can profile flow or at least pressure. It works with nine bar, with profiling you get more out.
Conclusion
The Option-O Lagom P80 ranks among the best grinders we've tested and on some days we'd say: it's the best. It delivers the most uniform particle distribution in our entire test field, virtually no retention, and a consistency that leaves few questions. Then there's this grind scale that takes some of that back.
Strengths: 0.2 grams of retention absolute, the best value we've measured. A main peak of 106 µm, narrower than any other grinder in the field. 0.04 grams standard deviation over five portions. Nine seconds for 18 grams with pleasant grinding noise and no heat generation. Plus RPM adjustment from 300 to 1,700 and static reduction that makes RDT from mandatory to optional.
Weaknesses: The grind display. One line is eight to ten seconds of extraction time, there are no intermediate markings, the reference line is too thick, and the spacing isn't consistent. Plus a knocker that occasionally gets stuck, and deep cleaning that requires a hex key.
For whom? For people who single-dose at home, write down their recipes, and enjoy truly understanding a coffee. Those who brew light specialty roasts and seek clarity and complexity get a fantastic tool here. And anyone with an espresso machine that can profile flow or pressure gets even more from this particle distribution.
Not for whom? For espresso beginners. The puck forgives little, without WDT you get channeling, and finding the right grind takes patience and practice. Those who just want a reliable espresso in the morning without worrying about extraction are happier with a less demanding grinder. In our comprehensive espresso grinder test you'll find more suitable candidates.
Price-Performance: For 1,600 euros or 1,799 francs, you get measurements you don't get elsewhere, top-level build quality, and a machine made to be user-serviceable. What you don't get for this money: a scale you can actually use to access this grinder's precision. That's frustrating because it would be the cheapest component in the whole machine.
In the video we mention around 2,000 euros. We based that on the grinder's size and the retail market, where it's listed at Coffee24 for 2,150 euros. Ordering directly from the manufacturer and shipping from Germany, it comes in significantly lower.
Test Results: Option-O Lagom P80
Ratings based on the KM Test Protocol for Espresso Grinders. All measurements self-conducted, blocks two and three at 1,100 RPM. Particle distribution intentionally doesn't factor into the rating colorwise because it's roast-dependent.
Technical Specifications Overview
| Property | Value |
|---|---|
| Price | Around 1,600 euros directly from manufacturer, shipped from Germany including tax; 2,150 euros at Coffee24; 1,799 CHF in Switzerland (as of September 2026) |
| Burr Size | 80 mm |
| Burr Type | Flat, Mizen 80OM Blind Burrs with integrated crusher |
| Burr Mount | Magnetic, 3-pin blind mount; alternatively two-screw burrs M6x7 |
| Operating Mode | Single Dosing (hopper up to 45 g, continuous feed possible) |
| Grinding Speed | 26.2 g / 10 Sec; 9 Sec for 18 g (at 1,100 RPM) |
| Noise Level | 82.8 dB(A) |
| Grinding Temperature | 26.0–29.9 °C (average 28.3 °C; beans 21.7 °C) |
| Absolute Retention | 0.2 g (0.1 g temporary, 0.1 g permanent) |
| Single-Dosing Deviation | 0.1 g |
| Consistency (Std Dev) | 0.04 g over 5 × 18 g |
| x50 Espresso (T4 / T7) | 144.8 µm / 172.3 µm |
| Main Peak (T4 / T7) | 106.0 µm / 110.0 µm |
| Fine Peak (T4 / T7) | 44.1 % / 39.8 % |
| x50 Ristretto (T5) / Lungo (T6) | 117.4 µm / 215.4 µm |
| RPM Adjustment | Yes, 300–1,700 RPM, detented |
| Grind Adjustment | Stepless, per manufacturer 10 µm per line; range Turkish to French Press |
| Motor | 500 W Brushless DC |
| Dimensions and Weight | 24 × 14 × 38 cm, 8.1 kg |
| Voltage | 100–120 V or 220–240 V |
| Special Features | Integrated slow feeding via screw, purge mode, auto-off via torque sensor, ionizer, knocker at outlet |
| Warranty | 1 year for manufacturing defects, thereafter lifetime support (manufacturer statement) |
As always, we tested this grinder according to our KM protocol and bought it ourselves. This test was not requested by Option-O.
















